What should you pay attention to when using UV curing oven?

What should you pay attention to when using UV curing oven?

 UV curing machine, ultraviolet UV curing oven is a machine that uses a UV lamp source to heat up the surface for drying and curing. UV curing machine is used for paper, PVC, plastic products using UV spraying, curing of the ink layer after printing. It is currently a more environmentally friendly way of drying inks. It can illuminate the UV lamp under the excitation of instantaneous high voltage to emit ultraviolet light with a main peak of about 360 nm, and irradiate the acrylic resin on the ink layer to crosslink and cure the acrylic resin. What should be paid attention to when using the UV curing oven? Then Juke Xiaobian will explain to you.

1. Is the grounding wire well grounded?
2. When the fan is not normal, please do not use it to avoid burning the UV lamp.
3. When the drive roller has a slight jump during the rotation, please tighten the tight screws at both ends of the drive roller.
4. When the machine has a serious fault, be sure to notify the manufacturer or dealer in time, and do not open the case by yourself.
5. When replacing the UV lamp, do not touch the lamp with your hand. Otherwise, it will cause defects on the UV lamp, affecting the luminous efficiency. You need to wear clean gloves for installation.
6. In order to prevent the life of the UV lamp from decreasing, do not cut off the total power supply immediately after turning off the light. Wait for the machine to automatically shut down before cutting off the main power switch.
7. When replacing the UV lamp, after opening the upper case, loosen the electric box fastening screw and pull out the light box for replacement.
8. When the UV lamp needs to be turned off, press the A lamp to stop, the B lamp stops the button and the fan continues to run. The UV lamp is cooled. After the lamp is cooled, the switchboard power is automatically cut off.

 Let's take a look at the UV UV curing oven HD picture:

UV curing oven

 UV curing oven

Large UV curing oven

UV curing oven customer figure 1

UV curing oven customer figure 2

UV curing machine site map 1

UV curing furnace site map 2

The above is what should be paid attention to when using UV curing oven? Introduction, if you need to buy or customize UV UV curing oven, please contact our company, contact our business staff for purchase or customization, thank you.

I am Dongguan Juke Industrial Development Co., Ltd., our company is a transformer automation production equipment supplier.

The following are the company introductions of our company and some automation equipments produced and supplied by our company. If you need to purchase or customize these equipments, you need to purchase or customize the transformer automatic production equipment. Please contact us and contact our business staff for purchase or customization. Thank you.

Dongguan Juke Industrial Development Co., Ltd. is a professional automation workshop production line solution provider for high frequency transformer peripheral equipment.

Juke Industry is dominated by Taiwanese technology, and all raw materials are selected and processed in strict accordance with Taiwan Standard Huai, and with the excellent technology and professional services to create maximum value for customers, and determined to become the world's high-frequency transformer automation equipment program The leading brand.
Juke Industry adheres to European standards. The product series include: transformer automatic inserter, ei type transformer inserter, transformer EI inserter, transformer core inserter, transformer automatic casing machine, Insulation casing automatic through machine，transformer core assembly machine, Transformer core assembly rubberizing machine, (automatic core assembly + bag tape + test + wobble plate),transformer winding machine, transformer automatic winding machine,Automatic Coil Winding Machine，transformer coil winding machine, transformer coil automatic winding machine, CNC winding machine, CNC automatic winding machine, CNC Coil winding machine, Coil Spindle Winding Machine，Single Spindle Winding Machine，single-axis CNC winding machine, single-axis coil winding machine, single-axis winding machine, double-axis winding machine, multi-axis winding machine, 6/8/16/12 axis automatic winding machine , 6/8/16/12 axis automatic transformer winding machine,Transformer Core Automatic Winding Machine， automatic winding + tape machine, (USB charger automatic film machine), automatic rubberizing machine, semi-automatic tape machine, transformer double pressing automatic Rubber laminating machine, transformer magnetic ring inductance double pressing automatic rubberizing machine, vacuum impregnation machine, (there are single and double cylinder differences: single cylinder automatic vacuum impregnation machine, double cylinder automatic vacuum impregnation machine), Vacuum pressure impregnation electric motor equipment，vacuum pressure impregnation process for transformers，Automatic Vacuum Impregnation Machine，vacuum pressure impregnation (vpi)，automatic soldering machine and semi-automatic Soldering machine (also called flip soldering machine), transformer flip welding Tin machine, transformer automatic flip soldering machine, double-head soldering machine, Angular Soldering Machine，Transformer Angular Soldering Machine，automatic dispensing machine, desktop automatic dispensing machine, full visual COB dispensing machine, computer cutting and stripping machine, magnetic ring inductor pulling and forming machine Magnetic core inductance automatic foot machine, magnetic ring inductance automatic foot machine, automatic locking screw machine, double Y axis coordinate type automatic locking screw machine, transformer filling vacuum defoaming machine, transformer automatic copper foil adhesive machine, automatic taping machine，Transformer Automatic Taping Machine，automatic coil taping machine，transformer core taping machine，automatic constant temperature Oven, transformer integrated tester, infrared tunnel furnace, UV curing oven, baking line，Transformer assembly production line，core automation production line and other high-frequency transformer peripheral automation equipment, products are widely used in high and low frequency transformers, ballasts and motor manufacturers. In order to meet the needs of the market, in 2008, an branch of Yixiu District, Anqing City, Anhui Province, formed a group of professional and technical personnel to provide quality services to customers.

The following is the contact information of our company. If you need to purchase or customize the products listed above, you need to buy or customize the transformer automatic production equipment. You can contact our company and contact our business staff for purchase or customization. Thank you.
Company Name: Dongguan Juke Industrial Development Co., Ltd.
 Contact: Phone / WeChat: 18819603799
               QQ: 3407993243
               Email:3407993243@qq.com
Manufacturer Tel: 0769-89870552
Company website: http://tc.huiyuecn.com
Address: Room 406, 4th Floor, Jupiter Industrial Park, Jufeng, No. 53 Shangnan Road, Shangjiao Community, Chang'an Town, Dongguan City